Search:

I believe it is still relatively easy to find the softback version? Certainly here in Italy there are always a few at the various shows and markets.

I ran a set of trumpets of differing lengths on an HSCC 1600HF several years ago with good results, I can vouch for them working.

I have two gearboxes surplus to requirements;

818-630 and 818.612 types.

Located in central England.

Do you mean the support that holds the carburettor assembly up? it is a simple (ish) bracket that has a rubber mount at the bottom end fixing to the oil filter housing whilst the other end is bolted...

I'd have to add these people; http://www.cicognaniguarnizioni.it/Lancia-132 quality is outstanding, I used them for all the seals and rubber part on my S2 Zagato restoration. As for do the use the...

Hi,

I think you are talking about the main nut on the end. I do not think there is anyway for the O-Ring to work. There is no detail (similar to a bi chamfer) for the seal to sit into, for it to...

I used this; https://www.woolies-trim.co.uk/product/1309/headlining-white I think.I'll send some images over the weekend.

Many years ago I had a 2000ie HPE with Digiplex which was also a non starter. I could not find any info on the unit but did have access to electronic test equipment. I opened the unit up and...

Woolies sell both of these in the UK

1975 would be Series 3. The dials are correct for a Series 3 car, they were black on Series 1 and 2. Not sure about the headlamp surrounds though. The badge on the rear says Fulvia 3 as well.

I had a similar fuss with my Sport, ran fine then simply would not start. I chased through the ignition and eventually found the distrbutor had slipped slightly and the plugs were fouled. In anycase...

The allen key the rounded tip is generically referred to as a 'Bondhus key' Bondhus make all sorts of keys with this ball/hex feature, can be found on Amazon etc..

Hi I have one, PM me for details. I am in the UK but happy to ship.

I have a complete Fulvia Berlina which I am not going to get round to restoring. Structurally it is pretty good, cosmetically it could benefit from some love. It would make an excellent shell/basis...

Is it to complete a tool kit as modern adaptors are available?

Does anyone know a source for the grille badge and back plate for an S2 Zagato? I'm going to be at a show in Italy at the start of March but if there is somewhere I can get hold of one before then......

I used this both on the floor rubbers and the fabric headlining;

https://www.amazon.co.uk/Evo-Stik-528-Contact-Adhesive/dp/B0001P03JC/ref=sr_1_1?ie=UTF8&qid=1548222483&sr=8-1&keywords=evostick+528

Really useful,

Thanks,

Over time rubber hoses can collapse internally and yet seem fine externally. Braided hoses tend not to do this but with these the braid degrades and can break up damaging the inner tube. Regular...

Bleeding the full circuit on a Fulvia can take a long time, it's just the way it is with the circuits on the car. To reduce this time I have used a proprietary kit that applies a small pressure (30...

If you have already removed the dash top and fascia it probably doesn't help to know you can change the bulbs with the all that in place.... anyway, you should be able to pull the whole binnacle out...

I know this has been discussed before but I cannot for the life of me find the thread.... I have a set of repro Fulvia alloy rims, unfortunately they appear to have had the hub machined for an S1...

As others have intimated, you need the belt. Without it the balance shaft is not being driven and the out of balance forces or 'tinging' are going to become a problem in terms of loads- engine wear...

Gogomobil?

I guess it depends on the supplier. I have a new sensor complete with washer.