Search:

Type: Posts; User: SubGothius

Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    1
    Views
    170

    For Sale: Re: Unusual Beta Coupe Restoration Project

    Here's that earlier thread, for anyone interested:
    http://www.lancisti.net/forum/showthread.php?10466-1979-Beta-Coupe-with-Zagato-SE-Wheels-and-Trim

    Good luck with the sale!
  2. Replies
    7
    Views
    296

    Re: Regulator/check valve at carb leaking

    The fact you have the pressure stabilizer fitted probably indicates the stock pump was a piston/reciprocating type.

    Please do followup here if you hear back from Pierce about that pin hole, been...
  3. Replies
    7
    Views
    296

    Re: Regulator/check valve at carb leaking

    That's primarily a fuel pressure stabilizer:
    https://www.piercemanifolds.com/product_p/b26570.htm

    It needs to be oriented vertically (arrow pointing up) to work properly, as it just holds a large...
  4. Replies
    11
    Views
    734

    Re: Engine dies. Boo.

    Do you have a starter relay wired in? If so, put'er in Neutral, pull the switched output wire from that relay (the one leading to the starter solenoid), and try touching that to battery (+). If it...
  5. Replies
    9
    Views
    355

    Re: Fuel line size 78 Beta Sedan

    Presuming it's set up like my Zagato and IIRC, the outboard barb goes to the tank, inboard barb to the engine. If you're replacing all the fuel lines (good idea anyway while you're at it), you could...
  6. Replies
    9
    Views
    355

    Re: Fuel line size 78 Beta Sedan

    For carb'd fuel pumps, I'm sold on the Carter gerotor type, part # P90091. You may need to remove the included filter that comes pre-clamped to the intake end, so you can reconnect with a longer span...
  7. Replies
    13
    Views
    1,053

    For Sale: Re: for sale 79 coupe and 82 zagato parts cars

    Or try Midwest-Bayless in Columbus, OH:
    https://www.midwest-bayless.com/contactus.aspx
  8. Replies
    3
    Views
    260

    Re: Beta Engine Vibration Stuts

    "Shot" as in how? Bushings on the ends perished, or are the actual damper plungers seized or move freely without any resistance? If it's just the bushings, you can have poly ones turned at any...
  9. Replies
    3
    Views
    228

    Re: Beta Bolt Size?

    Also note: the cam cover hold-down nuts should only be SNUG by hand. I screw them down finger-tight, then hold an Allen socket in my palm like a screwdriver to give them one last little twist, and...
  10. Replies
    6
    Views
    576

    Re: Beta P.W. Retro Help Needed

    I gather the cables, channels, etc. should only be oiled, not greased; apparently grease is just too thick and goopy for the low-effort operation required.
  11. Replies
    17
    Views
    956

    Re: High IDLE 1977 Beta saloon 2000

    1979 was the first year for the 2000 engine in the US.



    I think he's referring to crank timing marks in particular being absent, which could happen with an early car if the timing belt cover is...
  12. Replies
    12
    Views
    1,057

    Re: 1975 Montecarlo Messicana

    Related thread:
    http://www.lancisti.net/forum/showthread.php?6427-Help-Please-Beta-Montecarlo-S1-color-code
  13. Replies
    6
    Views
    620

    Re: Gearbox Oil Recommendation

    IIRC, one of the other problems with GL5 oils formulated for modern hypoid gears is they're too slippery for old-fashioned synchro designs to get the friction they need to function properly, which...
  14. Replies
    17
    Views
    956

    Re: High IDLE 1977 Beta saloon 2000

    According to the Haynes manual, jetting for a 2000 engine 34 DATR should be:

    Primary Idle Jet: 50
    Primary Main Jet: 120
    Primary Main Air: 170
    Primary Main Emulsion: F.30
    Secondary Idle...
  15. Replies
    1
    Views
    246

    Re: Lancia Beta transaxle seal sizes

    Seems like this thread has the info you're looking for:
    http://www.lancisti.net/forum/showthread.php?9653-Beta-Scorpion-trans-ring-nut-anyone
  16. Replies
    11
    Views
    1,036

    Re: Scorpion bumpers, top, nose band

    My interpretation would be that's just saying it's not required to completely remove the fabric, as the DB top would fit with the fabric left intact, tho' the straps and the rest of the rear...
  17. Replies
    11
    Views
    1,036

    Re: Scorpion bumpers, top, nose band

    Re: TMH's double-bubble roof, pretty sure they just mean it will not work with the fixed-roof "coupe" variant (never sold in the US) but, rather, only with the retractable-roof "spider" variant...
  18. Replies
    34
    Views
    2,821

    Re: Dual Weber Carb Kits?

    The issue isn't the angle, which is indeed the same for all Beta-engined models, though of course a manifold meant for Fiat models won't have the correct angle for any Beta. However IIRC, the Alquati...
  19. For Sale: Re: (almost) NEW Lancia Beta transaxle, or parts, for sale

    Could be something they started doing when they introduced other final-drive ratios and/or started stocking replacement units; if so, these might reasonably be presumed to have the earliest ratio...
  20. Re: 1981 pagato don't know if i should paint or sell

    Agreed on leaving the paint as-is if you're going to sell it anyway; you probably won't get a return on the investment of a decent paint job, and a cheap Maaco/Scheib job may not help it sell anyway...
  21. Replies
    5
    Views
    943

    Re: Beta cam identification

    With hot carbs, hot cams would make sense to take better advantage of the better breathing. AFAIK, only FI Betas came with cam-end driven dizzys as stock; however, that dizzy mount may have been a...
  22. Replies
    5
    Views
    943

    Re: Beta cam identification

    No idea if they're aftermarket cams but probably not; they appear to be for a Beta with fuel injection, going by the distributor drive slot on the end of the exhaust cam.
  23. Replies
    5
    Views
    911

    For Sale: Re: 1981 Lancia Beta for sale or part out

    If you're on Facebook, I'd suggest posting this in the groups Lancia Beta Appreciation Society:
    https://www.facebook.com/groups/9048585449/

    ...and Fiat & Lancia Friends:...
  24. Replies
    21
    Views
    2,785

    Re: How Many 82 Zagatos Remain ?

    According to Brian Long's Lancia Beta collector's guide book, there were 2,076 '79-81 Zagatos imported and only 791 '82s, no further breakdowns given by year. I'm not sure the VIN can be decoded to...
  25. Replies
    4
    Views
    621

    Re: s3 Instrument Binnacle removal ?

    By s3 I infer you mean a Fulvia 3, which is really just an s2 with some cheapened/updated trim materials (e.g. plastic grille and steering wheel, etc.), so the engineering per se is no different from...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4