Search:

Type: Posts; User: LanciaPaul

Page 1 of 10 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    3
    Views
    395

    Re: Rear brake porportioning valve

    For the $50 it cost, I'd would replace it rather than remove it. It is safety related and I would hate to find out how effective it was after the accident. ;-) It's function is basically to back-off...
  2. Wanted: Re: 1981/82 Power Steering Rack & Pinion or Rebuilder Reference

    One guy on here used to use these guys:

    https://www.steerandgear.com/services

    I think the story is that it is a very similar rack to a contemporary Audi 5000.

    Good luck!
  3. Replies
    1
    Views
    304

    Re: Lancia Beta Spyder 1981 Paint Codes

    I uploaded a 1981 PPG color code sheet to the downloads section of this forum. Back then, black is pretty much universal. Ditzler 9000.
    But the Lancia code is 601/122
    PV
  4. Replies
    12
    Views
    1,292

    Re: Engine dies. Boo.

    Which would seem to indicate that the spare switch was worse off than the original (all other things being equal) but it does not necessarily exonerate the original switch.
    Also to clarify, in your...
  5. Replies
    12
    Views
    1,292

    Re: Engine dies. Boo.

    I vote ignition switch too.
  6. Replies
    3
    Views
    459

    Re: 82 Lancia Zagato colour

    BTW...just uploaded the PPG 1981 colors to the "Downloads" section of this website.
  7. Replies
    3
    Views
    459

    Re: 82 Lancia Zagato colour

    PPG #72483
    http://www.autocolorlibrary.com/aclchip.aspx?image=1981-Lancia-pg01.jpg
  8. Replies
    9
    Views
    1,130

    Craig's List: Re: Restored Beta Coupe, nicely done

    I resemble that remark ;-)

    Lovely Coupe. Anyone know who's it is?
  9. For Sale: Re: (almost) NEW Lancia Beta transaxle, or parts, for sale

    Lancia did stamp the ratio on the outside of the 'box in 1981. Can't say for sure if they did it before that or not. It's by the LH output on the back side by the shifter.

    14567
  10. Replies
    4
    Views
    852

    Re: Any HPE's in the Midwest??

    I found out where John's old car is (NY/NJ) and also found one in Hamilton, Ontario that looks promising. Thanks for the reply, Dave!

    PV
  11. Replies
    4
    Views
    852

    Any HPE's in the Midwest??

    I'm looking for a quality HPE in the Midwest for a high-end car show. Anyone know of any around?
  12. Replies
    34
    Views
    13,622

    Re: Lancia Clubs in the USA

    Some excellent points on this resurrected thread. I used to be involved in FLU when it was Fiat Lancia Unlimited, was a member of the ALC and was a member of the LMC. This is all during the '90s in...
  13. Replies
    15
    Views
    2,178

    Re: Timing Question

    Oh boy, wait until you see that exhaust manifold set-up! Open-end wrench access only for the top part of the manifold to lambda sensor part of the manifold. You really have to try to tighten the heck...
  14. Replies
    15
    Views
    2,178

    Re: Timing Question

    Great news!
    Maybe your suspicions on the injectors leaking is true. I sent mine to this witchhunter guy and he did a nice job. I have to tell you, I sent him my spare set that had sat for well over...
  15. Replies
    15
    Views
    2,178

    Re: Timing Question

    The FI cars are so much nicer than the carbed '79s in my opinion. A little work now will pay big rewards later.
    These little gizmos are helpful to determine if your injectors are firing:...
  16. Replies
    15
    Views
    2,178

    Re: Timing Question

    If it won't run on starter fluid and has 180psi across the board, it can only be spark/timing related, no? Sounds like a fun adventure to put the puzzle back together again. I had an Alfa Milano that...
  17. Replies
    15
    Views
    2,178

    Re: Timing Question

    People really get hung-up on this. Same thing with the SOHC motors. Simply put, #1 and #4 are at TDC at the EXACT same time. If you put a timing light on your car and look at the marks, it will not...
  18. Replies
    17
    Views
    2,331

    Re: 1981 Beta Under hood Ignition Help

    OK, I have the big red wire in your picture #1 going right to the (+) battery post. I modified my harness a bit (because it is such a mess from the factory) so I don't see those other wires in...
  19. Replies
    17
    Views
    2,331

    Re: 1981 Beta Under hood Ignition Help

    I'll look tonight and get back to you on the other wires. This one I know.
    14269
    This being an Auxiliary Air Valve
    https://www.midwest-bayless.com/images/Product/large/1626.jpg
  20. Replies
    17
    Views
    2,331

    Re: 1981 Beta Under hood Ignition Help

    I read a little more and seems some guys saying up to 2 ohms is okay and some say as low as 0.4 is okay. So maybe my range is a little tight. In any event, 2.4 seems like it is outside of most...
  21. Replies
    17
    Views
    2,331

    Re: 1981 Beta Under hood Ignition Help

    I've always read that for a coil, there should be 1.4-1.8 ohms between terminals and 8,000-12,000 ohms between either terminal and the tower.
  22. Replies
    17
    Views
    2,331

    Re: 1981 Beta Under hood Ignition Help

    ^^^^Sage advise that might not be intuitive that will save you a lot of grief^^^^

    Only thing I will add is that even though this is an obscure Italian car, the ignition system is not really...
  23. Replies
    17
    Views
    2,331

    Re: 1981 Beta Under hood Ignition Help

    All accurate. It has a GM module like you suspected. It is bolted to an aluminum finned casting that is attached to the left hand shock tower (there is also some grease/goo between it an the casting...
  24. Replies
    12
    Views
    1,986

    Re: RR Brake Caliper Problem

    http://www.lancisti.net/forum/showthread.php?9019-Brake-caliper-overhaul-Rear
  25. Replies
    12
    Views
    1,986

    Re: RR Brake Caliper Problem

    Did you ensure that the slot in the piston is engaging the little nub on the back of the inboard pad?
    As an aside, I recently bought a set of rear pads that did not have the little nub on them so I...
Results 1 to 25 of 250
Page 1 of 10 1 2 3 4