Lancisti Community - Powered by vBulletin
  • Register
  • Help
  • Home
    • Articles
  • What's New?
  • Forum
  • Groups
  • Blogs
  • Link Directory
  • Downloads
  • Advanced Search
  • Home
  • Home
  • Articles
  1. PLEASE NOTE: If you wish to register but do not provide your REAL first AND last (sur) names, location (City), AND correctly answer the User Validation question when you register, your request will be automatically denied. If this is your first visit, be sure to check out the FAQ by clicking the link above. You must to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.

  • New Forum Posts

    DJ

    Re: Scorpion safety

    A few years ago a friend lost control of his Scorpion on some light snow in the mountains above Golden, Colorado. He ended up upside-down in a ravine

    DJ 20th August 2017, 04:02 PM Go to last post
    lancialulu

    Re: 818.342 Variante 1014 HF Tuning

    I have seen 1014 cam data sheet to indicate same as used in 1016 but also amended spec that has 4deg additional duration on exhaust....

    lancialulu 20th August 2017, 03:56 PM Go to last post
    impaw

    Re: 818.342 Variante 1014 HF Tuning

    thank you!

    impaw 20th August 2017, 03:48 PM Go to last post
    lancialulu

    Re: 818.342 Variante 1014 HF Tuning

    Higher compression (11.3:1) no air filter, lightened conrods, nitrided crank, 40mm solex / 34mm chokes, revs to 7200, cam lift and duration longer /higher.....

    lancialulu 20th August 2017, 03:47 PM Go to last post
    1,6 HF

    Re: Scorpion safety

    Both the X1/9 and the X1/20 were designed to meet what Fiat presumed were to be very rigorous new US crash standards; both cars are very robust.

    1,6 HF 20th August 2017, 03:45 PM Go to last post

  • Articles RSS Feed

    Installing a Beta gearbox into a Scorpion/Montecarlo 

    by
    DJ
    • View Profile
    • View Forum Posts
    • Private Message
    • View Blog Entries
    • Visit Homepage
    • View Articles
    Published on 7th June 2017 09:35 PM

    A few years back I installed an NOS gearbox from a Beta VX into my Scorpion WITHOUT disassembling, reaming out the shift-shaft, and reassembling, which, was the normal approach that people took. I promised to do a write up and I was just asked by a user to fill him in on what I had done. So here goes. ...
    Read More Read More 11 Comments

    Lancia Beta timing belt change procedure & tips 

    by
    SubGothius
    • View Profile
    • View Forum Posts
    • Private Message
    • View Blog Entries
    • Visit Homepage
    • View Articles
    Published on 18th September 2010 12:20 PM     Number of Views: 21553 

    This article explains the procedure for changing the timing belt on a Lancia Beta/HPE/Zagato, and is also largely applicable ...
    Read More Read More 5 Comments

    DMTR/DATR/DATRA carb adjustment guide 

    by
    FiatFactory
    • View Profile
    • View Forum Posts
    • Private Message
    • View Blog Entries
    • View Articles
    Published on 14th June 2010 12:08 AM



    Problems with DMTR/DATR/DATRA carbs can usually be grouped into three categories, vacuum leaks, idle passage ...
    Read More Read More

    • Latest Files

      1,3 HF homologation document

      Gamma Coupe Colour Chart 1981/82

      Gamma Berlina Colour Chart 1981/82

      Tectyl treatment for a Fulvia

      Lancia Beta Zagato badge decals

    • Recent Blog Posts

      Todd D.

      Building a 1/20 scale Lancia D-50 #7

      Hello,
      I've written out long winded posts about the D-50 progress and tried to post it with...

      Todd D. 14th August 2017 07:51 PM
      Todd D.

      Building a 1/20 scale Lancia D-50

      The rear de-dion tube sits on a cast aluminum housing connected to the leaf spring and transaxle....

      Todd D. 3rd August 2017 10:51 AM
      Todd D.

      Building a 1/20 scale D-50

      The D-50 is progressing well. The basic chassis is complete after alot of fiddling with the tubes...

      Todd D. 27th July 2017 08:56 AM
      Todd D.

      Building a 1/20 scale D-50

      Work on the real Lancias continues with the Scorpion having its rear 3/4 windows re-glued into...

      Todd D. 22nd July 2017 08:40 PM
      N. Tony Fasola

      Scorpion Window track

      Try to do a different project everyday on my ground up Scorpion project. To that end, today is...

      N. Tony Fasola 16th July 2017 01:45 PM
    • Contact Us
    • Lancisti Community Home
    • Archive
    • Top
    All times are GMT -5. The time now is 09:42 PM.
    Powered by vBulletin® Version 4.2.5
    Copyright © 2017 vBulletin Solutions Inc. All rights reserved.
    Copyright © 2002-2017, Classic Interests